產品搜尋

分　類：
關鍵字：

首頁 > Power/Data-Cable(進口電線電纜)> Fireproof-Fire Resistant LSOH Sheathed Cables(FIREFLEX) 耐火級低煙無毒電纜線 > CALEDONIAN-Fire Resistant Fire Alarm Cables (950°C 180 minutes)耐火級低煙無毒火警警報電纜線

CALEDONIAN-JE-H(St)H Fire Resistant 300V Mica+LSZH Insulated & LSZH Sheathed Fire Alarm Cables (950°C 180 minutes) 多對型雲母帶耐火級低煙無毒鋁箔隔離火警警報電纜線

5543606

商品編號: CALEDONIAN-JE-Bd

CALEDONIAN-JE-H(St)H Fire Resistant 300V Mica+LSZH Insulated & LSZH Sheathed Fire Alarm Cables (950°C 180 minutes) 多對型雲母帶耐火級低煙無毒鋁箔隔離火警警報電纜線

APPLICATION
The cables are used for the internal wiring of building when the circuit integrity during fire is
paramount. The cables are intended for use in fire fighting plants with mica tapes, with and without
Aluminum foil and LSZH outer sheath.The fire alarm cables with 30 to 90 minutes circuit integrity
should be used for control voltages and data transfer in alarm and fire alarm systems, where a
system circuit integrity E30/E60/E90 depending on lay system in accordance with DIN 4102-12 is
required. The circuit integrity is guaranteed with a test voltage of 110V.
STANDARDS
Basic design to VDE 0815

★★★★商品說明★★★★

PRODUCTS

Fire Resistant Fire Alarm Cables
300V Mica+LSZH Insulated & LSZH Sheathed Fire Alarm Cables
FFX200P 05mROZ1-R (CU/MICA+XLPE/OSCR/LSZH 300/500V Class 2 )
APPLICATION
The cables are designed, manufactured and tested as data transmission cables for emergency services. These are primarily intended for for indoor instrumentation and control cabling, electrically noisy environments and fire alarm systems in office buildings when high frequency signal transmission has to be assured in the event of a fire.
STANDARDS
Basic design to BS 7629-1
FIRE PERFORMANCE

Circuit Integrity	IEC 60331-21; BS 6387 CWZ; DIN VDE 0472-814(FE180); CEI 20-36/2-1; SS229-1; NBN C 30-004 (cat. F3); NF C32-070-2.3(CR1)
System circuit integrity	DIN 4102-12, E30 depending on lay system
Flame Retardance (Single Vertical Wire Test)	EN 60332-1-2; IEC 60332-1-2; BS EN 60332-1-2; VDE 0482-332-1 ; NBN C 30-004 (cat. F1); NF C32-070-2.1(C2); CEI 20-35/1-2; EN 50265-2-1; DIN VDE 0482-265-2-1
Reduced Fire Propagation (Vertically-mounted bundled wires & cable test)	EN 60332-3-24 (cat. C); IEC 60332-3-24; BS EN 60332-3-24; VDE 0482-332-3; NBN C 30-004 (cat. F2); NF C32-070-2.2(C1); CEI 20-22/3-4; EN 50266-2-4*; DIN VDE 0482-266-2-4
Halogen Free	IEC 60754-1; EN 50267-2-1; DIN VDE 0482-267-2-1; CEI 20-37/2-1 ; BS 6425-1*
No Corrosive Gas Emission	IEC 60754-2; EN 50267-2-2; DIN VDE 0482-267-2-2; CEI 20-37/2-2 ; BS 6425-2*
Minimum Smoke Emission	IEC 61034-1&2; EN 61034 -1&2; DIN VDE 0482-1034-1&2; CEI 20-37/3-1&2; EN 50268-1&2; BS 7622-1&2
No Toxic gases	NES 02-713; NF C 20-454

Note: Asterisk * denotes superseded standard.
CABLE CONSTRUCTION
Conductors: Plain annealed copper wire, stranded according to IEC(EN) 60228 class 2.
Insulation: Mica glass tape covered by extruded cross-linked XLPE compound or cross-linked compound type EI5 as per BS 7655: section 5.1.
Cabling Elements: Insulated cores are twisted to form pairs with varying lay length to minimize crosstalk. Two-pair cable had four cores laid in quad formation.
Cabling: Pairs are cabled together. In cables with 8 pairs or more, 4 pairs are assembled to form a bunch, the bunches are then cabled together.
Overall screen: Aluminum/polyester tape with tinned copper drain wire.
Outer Sheath: Thermoplastic LSZH compound type LTS3 as per BS 7655-6.1 (Thermosetting LSZH compound type SW2-SW4 as per BS 7655-2.6 can be offered.)
COLOUR CODE
Insulation Colour: According to IEC 60189-2 (other colour code on request).
Sheath Colour: Colour red (other colours on request).
Physical AND THERMAL PROPERTIES
Temperature range during operation (fixed state): -30°C - +90°C
Temperature range during installation (mobile state): -20°C - +50°C
Minimum bending radius: 8 x Overall Diameter

　